Just How To Install A Bathtub (For Novices).
Just How To Install A Bathtub (For Novices).
Blog Article
Are you on the lookout for ideas on A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably challenging project. If the old tub is readily obtainable, the job can move quickly; if you have to open up a wall surface to remove the old tub and place the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Ensure you have actually certified yourself for the job and fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is better to take into consideration utilizing one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have actually currently purchased a brand-new bathtub and also don't need to alter the setup of your previous water system pipes.
Your devices as well as material list must comprise the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub up until the spirit level reads level.
To set up taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the water supply and examine all joints as well as new pipework for leakages and also tighten them if needed. Fill the bath tub as well as also examine the overflow outlet and the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub must wait until the bath tub has actually been used at the very least when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washers are in location in between the tap and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to split a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Post feedback below. We'd be glad to listen to your responses about this post. Hoping to see you back again later on. You should take the time to share this post if you enjoyed reading it. Thanks for taking the time to read it.
Suggested Site Report this page